Page 977 - LMS_Catalog_65
P. 977

 HOSE & CLAMPS
965
 Water/Heater Hose
Series 130
Low Permeation Marine Fuel Hose
Series 368 Type A
   mfr
SHI
mfr
SHI
This Water/Heater Hose is fabric-reinforced and has an EPDM tube and cover. This hose is primarily used for engine heater hose, heat exchanger, A/C circulation, and drain lines (sink, icebox, shower and livewell). It is resistant to mild chemicals, heat, cold, ozone and saltwater.
Size Part No. Per Foot Working PSI
1/2" 16-130-0126 $1.94 62
5/8" 16-130-0586 $2.14 62
3/4" 16-130-0346 2.80 50 Water/Heater Hose
Low permeation marine fuel hose has a plastic barrier veneer with an outer layer tube to limit permeation. This polyester reinforced hose complies with EPA and CARB very low permeation requirements and is weather/UV resistant. This hose is primarily used for fuel feed (gasoline up to 85% ethanol blended fuels/diesel/all bio-diesel blends). It meets USCG Type A1 - 15 requirements for pleasure boats and meets SAE J1527 Type A1-15, ISO 7840 Type A1, and NMMA/CE type accepted standards. The temperature ranges from -20F to 212F.
  Size Part No. Per Foot
1/4" 16-368-0140 $2.71
5/16" 16-368-0560 $2.90
3/8" 16-368-0380 $3.00
1/2" 16-368-0120 $3.86
Silverado 4000 Fuel Line
   Series 160
50' Box Per 50' Box
16-368-0146 $156.65
16-368-0566 $164.44
116-368-0386 $168.96
 116-368-0126 $223.25
  mfr
SHI
Series 337
 Water/Heater Hose has a good bend radius, is fabric reinforced, and has an EPDM tube and cover. This hose is primarily used for critical water connections, heat exchanger, toilet intake, small engine intake, bilge pump intake/discharge, and below water line drains and scup- pers. It is resistant to mild chemicals, heat, cold, ozone and saltwater. Working PSI: 250
Size Part No. Per Foot
1/2" 16-160-0126B $3.27
5/8" 16-160-0586B $3.08
3/4" 16-160-0346B $3.64
1" 16-160-1006B $4.60
mfr
SHI
Silverado 4000 fuel line is constructed with a non-permeable THV barrier layer, polyester reinforcement, and a CPE weather and UV resistant cover. It meets all current EPA and CARB standards. The hose construction is easier to rig, clamp and maintains its flexibility under a range of extreme environmental conditions.
 Size Part No.
3/8" 116-337-0380
5/16" 116-337-0560
Fire – Alcohol Fuel Fill Hose
Per Foot 50' Carton
$2.74 116-337-0386
Per Carton
$162.00
$156.42
   $2.57 116-337-0566
  mfr
90° Rubber Elbow EPDM
SHI Series 290
Series 350 Type A
  Shields 90° rubber elbows are made of 100% high temperature EPDM rubber and have a maximum operating temperature of 250°F (121°C).
mfr
SHI
Size Part No.
2" 116-290-2000-1
2-1/2" 116-290-2120-1
3" 116-290-3000-1
3-1/2" 116-290-3120-1
4" 116-290-4000-1
5" 116-290-5000-1
6" 116-290-6000-1
8" 116-290-8000-1
Hump Hose Connector EPDM
Series 220
Shields hump hose connectors are made of 100% high temperature EPDM rubber and have a max- imum operating temperature of 250°F (121°C).
Each
$28.31
$32.27
$33.30
$39.34
$46.07
$58.64
$70.92
Shields Fire-Acol Fuel Fill Series 350 offers a solution to this issue. Fire-Acol uses a buna-n-vinyl cover that is very resistant to ethanol fuel. The hose will withstand exposure to fuel stored in the hose after refueling.
   Size Part No.
1-7/8" 16-350-1780
2" 16-350-2000
2-3/8" 16-350-2380
Fuel Fill Hose
Per Foot
$18.61
$20.16
     $182.56
$23.40
   mfr
SHI
Series 355 Type A
  Size Part No.
3" 116-220-3000-1
3-1/2" 116-220-3120-1
4" 116-220-4000-1
5" 116-220-5000-1
6" 116-220-6000-1
8" 116-220-8000-1
Each
$30.20
$38.64
$39.17
$42.60
$47.45
$121.70
Shields Fire – Acol – Fuel Fill Hose resists gasoline/alcohol blends and is compounded for low permeation. It is abrasion resistant and it is reinforced with wire helix imbedded between piles of HD synthetic cord. This imported hose is primarily used for fuel fill (gas or diesel) and is for pleasure boats only.
Size Part No. Per Foot
1-1/2" 16-355-1120 $11.25
mfr
SHI
     We cut most hose to custom lengths in Per Foot increments. Cost savings on boxes if available.
Please contact us for clamp sizes. 1-800-327-3792
 EXHAUST/WATER & FUEL HOSE
   975   976   977   978   979