Page 934 - LMS_Catalog_65
P. 934

 922
ENGINE ACCESSORIES
 Rigging
   The cable boot is constructed of rugged
black vinyl that resists ultraviolet rays,
gasoline and oil. Other manufacturer boots are made of rubber which will degrade in the marine environment. This cable boot is available in three sizes to cover all installation requirements.
In order to get the best fit, please note the following measurements:
• 4.5” Cable Boots are designed to cover a 4.5” hole, so the inner diameter is 4.5” and outer diameter is 5.710”.
• 3” Cable Boots are designed to cover a 3” hole, so the inner diameter is 3” and outer diameter is 4.122”.
• 2” Cable Boots are designed to cover a 2” hole, so the inner diameter is 2” and outer diameter is 3.1”.
Cable Boot Grommet
CB-1-DP
CBR-2-DP
Part No.
CB-1-DP
CB-1W-DP
CB-2-DP
CB-4-DP
CB-4W-DP
CBG-1-DP
CBG-2-DP
CBG-4-DP
CBK-4-DP
CBR-1-DP
CBR-1W-DP
CBR-2-DP
CBR-4-DP
CBR-4W-DP
CBS-4-DP
CBR-4-DP
Description
Cable Boot - 3” Boot - Black
Cable Boot - 3” Boot - White
Cable Boot - 2” Boot - Black
Cable Boot - 4-1/2” Boot - Black
Cable Boot - 4-1/2” Boot - White
CBS-4-DP
T-H FLEXTM Flexible Sleeving
   mfr
T/H
Zippered Rigging Sleeves
Protect your cables and hoses with this easy to remove rigging sleeve. Made of rugged Sunbrella® fabric, this sleeve will withstand the elements and resist fading. Easily zips on and off to access cables of hoses when needed. Ends are secured with cable ties sewn into pockets.
mfr
T/H
Part No.
ZRS-1-DP
ZRS-2-DP
Cable Boot
Description
48” Black
28” Black
Part No.
FLX-125-DP
FLX-50-DP
FLX-75-DP
Description
1-1/4” diameter, 50 ft. spool
1/2” diameter, 100 ft. spool
3/4” diameter, 100 ft. spool
T-H FLEXTM is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEXTM offers total protection for wire and cable assemblies. The unique expan- sion characteristics makes T-H FLEXTM easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEXTM expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.
     Cable Boot & Accessories
 mfr
T/H
Cable Boot Reinforcing Rings
   CBR-1-DP
          Fits underneath T-H Marine cable boot
to provide a internal sleeve to protect
cables, hoses and wires from chafing
against a rough hole cut or sharp edge.
Fits into pass-thru hole for steering,
electrical and control cables and provides a smooth, chafe- free fitting. Cable boot fits snugly onto top of grommet.
Packaging: bulk, distributor standard pack 50 skin pack. 12 per carton.
Cable Boot Grommet - Fits CB-1, 3” Cable Boot - Black
Cable Boot Grommet - Fits CB-2, 2” Cable Boot - Black
Cable Boot Grommet - Fits CB-4, 4.5” Cable Boot - Black
Cable Boot - 4-1/2” Boot with Ring - Black
Cable Boot Reinforcing Ring - Fits CB-1 - Black
Cable Boot Reinforcing Ring - Fits CB-1 - White
Cable Boot Reinforcing Ring - Fits CB-2 - Black
Cable Boot Reinforcing Ring - CB-4 - Black
Cable Boot Reinforcing Ring - Fits CB-4 - White
Cable Boot, Split, 4-1/2, with mounting ring
   CBG-2-DP
   RIGGING















   932   933   934   935   936