Page 930 - LMS_Catalog_65
P. 930

  ENGINE ACCESSORIES
BETTER THAN THE OEM PROPELLER
*Note: To find the correct installation kit and propeller housing, locate the HP, gearcase size, and prop shaft spline count of your outboard or sterndrive.
918
  0
40-150hp
ENGINES WITH A
4.25” GEARCASE
500 Series Installation Kits
Use on engines under 200hp with aluminum or stainless steel props or engines 200hp and above with aluminum props only.
Premium corrosion resistant brass splines. Eliminate hub system vibration & chatter. Reduce gear shock & engine/drive damage. Reduce prop replacement cost by up to 50%.
500 Series MasterGuard Installation Kits
& Corresponding Prop Housings are
Compatible with, and Upgrade Competitors’
Hub & Prop Systems. Interchangeable with
®®® Mercury Flo-Torq II , Michigan Wheel
®®
XHS , Solas RubexTM hub kit systems.
NOTE: Not applicable with Turning Point’s 10, 20 and 200 Hub Kit series.
AN INSTALLATION KIT IS REQUIRED
MasterGuard Kits include a Lifetime Warranty
FOR PROPS LISTED TO THE RIGHT
503
506 11500600
501 11500100
501 11500100
507 11500700 501
505 11500500
507 11500700
503 11500300
500 11500000
506 11500600
509 11500900
501 11500100
500 11500000
505 11500500
       Engine Brand - Various Splined Prop Shafts
Kit
MFG. Part #
Each
    EVINRUDE® & JOHNSON®: (13 spline shaft)
2 cyl: 50hp ('71-'74) / 45 to 55hp commercial
3 cyl: 55, 60, 65, 70hp, 75hp with large gearcase, 65hp commercial 4cyl:75,85,88,90,100,110,115,120('86-'94),125,135('73-'76),140('77-'84,'86-'94) / H.O. (includes E-TEC H.O.): 60, 90, 115hp
E-TEC: 40, 50, 60, 65, 75hp / 20” shaft: 90, 115hp (not pontoon series), 130hp ('09-'10)
11500300
$58.00
       MERCURY® &MARINER®:Note:PropsNotAvailablefor'77&Oldermodels.(15spline shaft)(2&4stroke)40to60Bigfoot &FourStrokeCT/70(‘87-’89)/75,80(‘78- ’89), 90, 100, 115, 125, 140hp / 150 XR4/6 (thru 1993, includes equivalent Mariner Magnum I, II, III.)
FourStrokeTM & SeaProTM 4cyl: 40 to 75hp / OptiMax: 75, 90, 115, 125hp
11500100
$58.00
      JOHNSON®: (13 spline shaft) 4 stroke ('98-'09): 60hp, 70hp
FORCE®: (15 spline shaft) 75hp ('99) / 90hp to 150hp ('95+) HONDA®: (15 spline shaft) ('95-'98): 75hp, 90hp
HONDA®: (15 spline shaft) P60 / 75, 90 (‘99+) / 100, 115 (not 115D), 130hp
NISSAN® & TOHATSU®: (15 spline)
60C, 70C, 70('02-'09) / (not BFT): 90 to 140hp / 115 TLDI ('14+)
NISSAN® & TOHATSU®: (15 spline shaft)
BFT ('14+): W60, 60, 75, 90hp
OMC®: (13 spline shaft)
Cobra 400: 2.3 to 3.0L ('78-'89) / Sea Drive: 1.6 to 1.8L
PARSUN®: (15 spline shaft) T60, T75, T85, T90
SUZUKI®: (13 spline shaft) DT 2 Stroke ('89+): 75 to 140hp / DF 4 Stroke ('98-'09): 60hp, 70hp
SUZUKI® & JOHNSON®: (use 4 blade props only)
4 stroke: (‘09+) 70A, 80A, 90A, 70, 80 / (‘01+) 90,
100, 115 (Not 115A)
SUZUKI® & JOHNSON®: (use 4 blade props only)
DF 4 stroke: 50AV, 60AV, 115A, 140, 140A
YAMAHA®: Note: If prop strikes trim tab, replace with Yamaha part #6E5-45371-10. (15 spline shaft)
High Thrust: FT50, FT60 / 2 stroke: 60 to 100hp / 4 stroke: 70, 75 ('03-'16), 80, 90 ('03- '16), 100hp
YAMAHA®: Note: If prop strikes trim tab, replace with Yamaha part #6E5-45371-10. (15 spline shaft)
2 stroke: 115 to 130hp / 4 stroke: 75 ('17+), 90 ('17+), 115hp
$58.00
$58.00 $58.00
$62.00
$58.00
$62.00
$58.00 $58.00 $58.00
$62.00
$58.00
$58.00
$58.00
                              new engineering CRANKs up BOAT PERFORMANCE
Stainless Steel Performance at Aluminum Prices
New unique blade geometry and manufacturing processes results in the highest performance aluminum propellers on the block. Hustler® propellers out performed most competitive stainless steel props in recent tests. Not only does top speed, handling and hole shot improve, but also mid-range performance, which will save you a ton in gas usage.
Squeeze Cast for Added Strength
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. It generates the highest mechanical properties attainable in a cast aluminum prop resulting from a tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors still use old Die-Cast processes that produce blades that flex, resulting in overall poor performance.
 TP-5
WARNING: MasterGuard Installation Kits Warning: This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
SPARK PLUGS











   928   929   930   931   932