Page 268 - LMS_Catalog_65
P. 268

 256
PUMPS
Ballast Puppy Wakeboard Towboat
Ballast Pump and Motor
mfr
JAB
The Jabsco 18220-1127 is a Ballast Puppy flexible impel- ler wakeboard towboat bal- last pump with a yellow Polyeurethane Impeller, Lip Type seal, 1/2 Inch NPT and 1 Inch External Hose Barb Ports, coupled to a 12 Volt DC Motor. These pumps can deliv-
er almost 80 pounds (10 gallons) of water ballast per minute. With a flow rate of 9 GPM (34 LPM), it can quickly add up to 80 pounds (40 kgs) of water per minute to ballast tank systems. The Pump ports have external 1 Inch hose barb and internal 1/2 Inch pipe threads. The motor on this pump is equipped with a Run-Dry Protection Device, and is a 12 Volt DC, Permanent Magnet Type, Fully Enclosed, with a Stainless Steel Shaft, and Ball Type Shaft Bearing. The pump cannot run against a closed outlet as may be encountered when installed in systems with valves to regulate flow. Pressure for normal operation should not exceed 20 feet of head (8.7 psi).
Part No. Each Volts
18220-1127 $310.59 12
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Ballast King Bronze DC Pump w/Reversing Switch
mfr
JAB
Ballast King 15 GPM Impeller Ballast Pump with Reversing Switch by Jabsco®. Utilizing this reversible flexible impeller pump technology, ballast sys- tems can be filled or emptied with the new Ballast King — 15 GPM. Ballast systems fitted
with our Reversing Polarity Switch can fill or empty ballast tanks with one pump in minutes. Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protected).
Part No. Each
22610-9507 $380.31
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Puffer Accumulator Tank
mfr
H/H
This compact 4.4-gallon pressure tank is designed for operation in seawater or freshwater. It’s constructed from deep drawn steel with a polypropylene liner, seamless butyl diaphragm and brass threaded connection. The exte- rior is undercoated with a crack-proof zinc based barrier coating that is top coated with white enamel. INCLUDES
pump bracket that matches X-caliber mounting pattern. 11" D x 11 1/2" H x 15" L Inlet 3/4" NPT. Maximum operating temperature 200°. Maximum working pressure 100 PSI.
Part No. Each
PT-102BK $328.55 FIG 6823
Jabsco Accumulator Tanks
   Snap-In Ports for 30573-0000
                          30649-1000
30651-1000
30654-1000
  mfr
JAB
Replacement Ports: 1/2" thread – 30649-1000 (for QEST type fittings) For 30573-0000 ONLY
30573-0000
FIG 116
30573-0000 is made of molded ABS plastic and has a capacity of approximately 1 quart and dimensions of approximately 13-1/4" L x 5" W. 30573-0000 has a precharged 18 psi bladder and can be mounted in any position and will not water log. Also, it INCLUDES snap-in 1/2" hose barbs that can be removed and replaced with 1/2" IPS fitting No. 30649-1000 sold separately.
Part No. Each Hose Size Description
30573-0000* $95.01 1/2" Accumulator Tank – Premium
 30649-1000** $5.43 pr. 1/2" IPS Straight Snap-In Pipe Fittings
 30642-1000 $5.43 pr. 3/4" 90° Snap-In Hose Barb
 30651-1000 $5.43 pr. 1/2" 90° Snap-In Hose Barb
      30654-1000
Straight Snap-In Hose Barb
$5.43 pr. 1/2"
*Optional Snap-In Fitting for Qest Type Fittings
 *
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Fresh or Salt Water Accumulator Tanks
FIG 7953
mfr
WSS
   T-5 – T-12 – T-25 –
ACCUMULATOR TANK SIZE
7.9" D x 10.8" L 10.6" D x 13.7" L 15" D x 15.7" L
   ACCUMULATOR TANKS reduce pump cycling and eliminate pul- sations and water hammer. Water is separated from air chamber by a butyl diaphragm in a FDA compliant polypropylene reservoir. Pressurized water volume is approximately 35% of total tank capac- ity at 30 PSI. Mounts horizontally, vertically, or upside down. Install as close as possible to the pressure switch.The greater the volume, the longer the pump cycle. Tanks are pre-pressurized @ 40 PSI total volume and must be fine-tuned to 2 PSI below cut-in pressure of pump. Maximum working pressure 150 PSI. Use with fresh or salt water up to 200°F. Use on cold water side of hot water heaters to prevent “spilling" of relief valves.
  Part No.
Each
Total Tank Capacity* 2.1 Gallons
4.8 Gallons
9.3 Gallons
Water System Pumps Parts
T-5
T-12
T-25
* Actual water volume will vary based on PSI.
IPS
3/4" NPTM 3/4" NPTM
1" NPTF
$102.90 $139.15 $308.20
    Diameter (in)
Height (in)
Total Volume (gal)
Inlet Fitting (MPT)
Drawdown 20/40 gals
Drawdown 30/50 gals
Drawdown 40/60 gals
Shipping Weight
11
11 3/4
4.4
3/4
1.6
1.4
1.2
9 lbs
mfr
FPI
Part No. Each
PWS01 $70.45 U1096A $20.70
U9-201 $4.95
Description
FPI Valve Gasket Kit for 2 and 3 way 40mm & 50mm Valves
Shaft Seal Assembly
O-ring 1-1/8" I.D. x 1-3/8" D x 1/8" W
   WATER SYSTEM PUMPS




   266   267   268   269   270