Page 120 - LMS_Catalog_65
P. 120

 108
GAUGES & SENDERS
   Floating Ground 340-001
340-020
Drive Tang
Part No. Each
340-001 $607.54 340-060 $18.43 340-061* $18.43 340-020* $108.38
Description
Floating Ground Sender
Drive Tang .152"
Drive Tang .187" Inductive/Magnetic Pick-Up Sender
Thread
7/8"-18
Sender and Drive Tangs
For Generator Tachometers and Synchronizers for Diesel Applications
VDO FIG 4108
340-001 can be used with VDO generator tachometers and synchronizers. The generator sender is installed with its shaft connected to the injector pump or camshaft of the engine. Up to four generator tachometers and two synchronizers can be operated from one generator sender. It is important to use the correct size drive tang for your engine. Check your engine specifications for correct drive tang size. 340-020 is for use with electronic and programmable tachometers and engine synchronizers designated as inductive type.
 mfr
     mfr
*   WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Engine and Gear Oil Pressure Senders
VDO FIG 4112
 Standard Ground
 All Pressure Senders are 12- or 24-Volt and have 1/8-27 IPS thread unless noted. These senders work with most VDO series gauges that are 10-180 ohms. Standard Ground: Single wire senders with positive lead only. Grounding occurs through the sender case to common ground. Floating Ground: Two wire senders with positive and negative lead. The sender is insulated in the engine block and grounding occurs through the negative lead to a common ground (i.e. ground on battery). This prevents the formation of a voltage leak and electrolytic corrosion. Dual Station: Dual gauge operation from a single sender. “D" is stamped on side of hex nut of sender.
   Part No. Each
360-003 $59.66 360-004 $59.80 360-009* $75.28
Station PSI
Single 80 Single 150 Single 80 Single 150 Single 400 Single 80 Single 150 Single 350
- 80 Dual 80 Dual 150 Dual 80 Dual 150 Dual 350 Dual 400
IPS
1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27
# on Sender
29/4 29/12 30/23 30/15 38/8 32/1 32/14 38/3 -
1/1 1/2 3/1 3/2 2/1 2/3
Ground
Standard Standard Standard Standard Floating Floating Floating Floating Standard Floating Floating Standard Standard Floating Floating
    Floating Ground
360-025 360-406 360-410 360-430 360-431 360-801 362-001 362-002 362-033 362-034 362-003 362-004
$75.42 $69.22 $64.60 $64.72 $67.52 $51.79 $76.14 $68.84 $62.02 $69.70 $80.28 $69.54
              A
mfr
VDO
FIG 4109
*   WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Temperature Senders
All are 12- or 24-Volt. Refer above for ground explanation. All work with most VDO gauges that are 10-180 ohms.
B
NOTE: DON’T use teflon tape or pipe sealants on senders tapered threads. *2 Terminals: One to set off alarm @ 7.0 PSI and the other for pressure.
      Part No.
323-095 323-416 323-419 323-420 323-421 323-425 323-478 323-479 325-002 325-007
250°F/120°C, 6-24V
Thread Number on Sender
1/8-27 IPS 801/5/1 14x1.5mm 801/1/26
Connection
Packard Slip-On Knurled Nut Knurled Nut
.250" Spade Knurled Nut Double .250" Spade Double .250" Spade Double .250" Spade Double .250" Spade Double .250" Spade
Each
$16.71 $23.82 $20.18 $25.52 $22.30 $52.22 $36.22 $38.60 $55.74 $55.35
$57.83
NOTE: DO NOT use teflon tape or pipe
One (1) terminal
Station
Single Single Single Single Single Single Single Single Dual* Dual*
801/1/16 801/1/9 801/1/38
Ground
Standard Standard Standard Standard Standard Floating Floating Floating Floating Floating
Terminal
D B B A B C C C C C
  1/2-14 IPS
1/4-18 IPS
3/8-18 IPS
14x1.5mm —
    1/2-14 IPS 3/8-18 IPS 1/4-18 IPS 3/8-18 IPS
805/1/4 805/1/5 805/3/1 —
    323-485
300°F/150°C, 6-24VA
Single
1/4-18 IPS —Floating
sealant on VDO tapered threads. *The “D" stamped on nut means it is a dual station sender. = standard ground. Two (2) terminals = floating ground.
CDouble .250" Spade WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
  SENDERS & DRIVE TANGS
C
D


















   118   119   120   121   122